Cleaning of grease stains on the hand-free mop in the restaurant kitchen

Strategies for cleaning grease from hand-free mops in restaurant kitchens

Mop pretreatment

Initial stain removal: If the mop head is stained with a large amount of oil, you can first wipe the surface oil with a paper towel or an old cloth to reduce the burden of subsequent cleaning.

Classification and treatment: Select the cleaning method based on the degree of oil stains. For light oil stains, direct soaking can be done, while for severe oil stains, solvent pretreatment is required.

Preparation of cleaning tools and materials

Solvent selection: For stubborn oil stains, organic solvents (such as trichloroethylene, banana water) or household substitutes (such as white vinegar, baking soda) can be prepared.

Detergent ratio:

Daily cleaning: Add an appropriate amount of white vinegar and laundry detergent to half a basin of warm water, stir well, and then use it to soak the mop.

Deep cleaning: Add baking soda, white vinegar and detergent to warm water (40-50℃), and let it stand for 15 minutes to dissolve the grease.

Soaking and dissolving

For light oil stains: Soak the mop head in the prepared cleaning solution for 10 to 15 minutes. During this period, you can gently turn the mop to fully dissolve the oil stains.

For severe oil stains: First, wipe the mop head with an organic solvent, then soak it in the cleaning solution. If necessary, extend the soaking time to 30 minutes.

Brushing and rinsing

Scrubbing: After soaking, use an old toothbrush or brush to gently brush the crevices of the mop head, especially the rubber cotton head or fiber layer, to remove any remaining oil stains.

Rinse: Rinse the mop head repeatedly with clean water until there is no cleaner left.

Dehydration and Drying

Dehydration: Use the dehydration function of the hand-free mop. Select the dehydration setting based on the degree of oil stains (for severe oil stains, you can choose the "wet mop" setting for a second dehydration).

Drying: Hang the mop in a well-ventilated area, avoiding direct sunlight, and ensure that the cotton head is completely dry to prevent mold.

Stubborn oil stains

Solvent pretreatment: Wipe the oil stains with trichloroethylene or banana water, and then soak them in cleaning solution.

Heating assistance: If the oil stains have solidified, you can soak the mop head in hot water (40-50℃) to soften the oil stains before cleaning.

Odor removal

Disinfectant soaking: Add a small amount of disinfectant to the cleaning solution, soak it, and then rinse it clean. This can remove odors and kill bacteria.

Baking soda and toilet water: Add baking soda, laundry detergent and a few drops of toilet water to the mop bucket, shake it and let it soak. This can remove odors and leave a pleasant fragrance.

Handle it immediately after use

Rinse with clean water: After each use, immediately rinse the mop head with clean water to prevent oil stains from solidifying.

Hanging storage: After cleaning, hang the mop in a well-ventilated area to prevent the mop head from touching the ground and avoid secondary pollution.

Regular deep cleaning

Frequency: Conduct a deep cleaning once a week, especially with mops around the dining area.

Method: Soak in oxygen-containing bleach (diluted at a ratio of 1:100) for 1 hour to thoroughly remove deep oil stains and bacteria.

Mop replacement

Replacement standard: When the mop is damaged, sheds fibers or its cleaning effect drops significantly, it should be replaced in time.

Replacement frequency: It is recommended to replace the mop once every quarter to ensure the cleaning effect.

Safety protection

Wear gloves: When using organic solvents or disinfectants, rubber gloves should be worn to avoid skin contact.

Ventilation and air exchange: Operate in a well-ventilated environment to avoid inhaling harmful gases.

Environmental protection treatment

Waste liquid treatment: The waste liquid after cleaning should be poured into the sewer to avoid random dumping and environmental pollution.

Solvent recovery: Organic solvents can be reused, reducing waste.

Mop selection

Material priority: Choose a rubber cotton head or microfiber mop, which has strong water absorption and is easy to clean.

Functional adaptation: Ensure that the mop has multiple dehydration functions to adapt to different levels of oil stains.